Basics · step by step

The path to CE, step by step

The CE marking is not a certificate someone issues to you. It is your declaration that the product meets European rules. We show what leads to it, what you can do yourself and where we save you time.

Reading time 7 minutes9 steps

The manufacturer is responsible for CE, i.e. whoever places the product on the market under their own name. A lab, a notified body or a parts supplier will not do it for you. They can, however, provide evidence and save you a lot of work.

  1. 1

    Identify which rules apply to the product

    For electronics, these are most often the EMC Directive (2014/30/EU), the LVD for electrical safety (2014/35/EU), the RED for radio equipment (2014/53/EU) and RoHS (2011/65/EU). Depending on the type of product, others are added, such as machinery rules.

    You can do it yourself: Write down what the product does, how it is powered, which interfaces it has and whether it contains a radio.

    Where we help: Our EMC and CE calculator identifies the rules and standards in a few minutes. EMC and CE calculator →

  2. 2

    Choose the conformity assessment procedure

    For EMC, LVD and RoHS, conformity is usually assessed by the manufacturer alone (module A, internal production control). A notified body is needed only in some cases, e.g. for radio equipment where harmonized standards have not been applied in full.

    You can do it yourself: Decide who will be the manufacturer, i.e. under whose name the product will be placed on the market.

    Where we help: We advise whether your own assessment is enough.

  3. 3

    Find the harmonized standards

    Directives say WHAT the product must meet. Harmonized standards say HOW to verify it. If you meet them, the presumption of conformity applies and you have the strongest evidence.

    You can do it yourself: Check whether a dedicated product standard exists for your type of product.

    Where we help: We select the standards and build a test plan from them.

  4. 4

    Assess the risks

    Describe the hazards the product may present (electric shock, overheating, interference) and how you prevent them. The risk assessment is part of the technical documentation.

    You can do it yourself: You know this best. A table is enough: hazard, measure, verification.

    Where we help: We check that the assessment matches the standards.

  5. 5

    Verify the product by testing

    Measurements to the standards: EMC, electrical safety, and climatic or IP protection tests where relevant. The results are the main part of the technical documentation.

    You can do it yourself: Prepare the sample, cables and a description of the operating modes.

    Where we help: Pre-compliance testing in our own EMC chamber, usually available within a week. If something fails, we help fix it. Preparation checklist →

  6. 6

    Compile the technical documentation

    Product description, schematics and drawings, list of applied standards, test reports, risk assessment and the user manual. It is kept for 10 years after the last unit is placed on the market and the market surveillance authority may request it.

    You can do it yourself: Most of it: description, schematics, drawings, manual and documents from your parts suppliers (declarations of conformity, RoHS).

    Where we help: We provide the test reports and input for the technical documentation.

  7. 7

    Draw up the EU declaration of conformity

    A single document in which the manufacturer declares that the product meets all applicable rules. It contains identification of the product and manufacturer, the list of rules and standards, place, date and signature.

    You can do it yourself: The declaration is drawn up and signed by the manufacturer, i.e. you.

    Where we help: We prepare the input and check that nothing is missing.

  8. 8

    Mark the product and include the manual

    The CE marking must be visible, legible and indelible, at least 5 mm high. The product must bear a type or serial number and the manufacturer’s name and contact address. The manual and safety information must be in the language of the country where the product is sold.

    You can do it yourself: The label, manual and translations.

    Where we help: We check the marking and the manual against the product standard.

  9. 9

    Keep an eye on the product after placing it on the market

    When you change the product (a different board, power supply, firmware with a new radio) or the standards change, reassess whether the declaration of conformity still holds.

    You can do it yourself: Keep a record of product changes and follow updates to the standards.

    Where we help: Quick retesting of the modified version. The calculator shows the price up front.

Mind cybersecuritySince 1 August 2025, cybersecurity requirements apply to internet-connected radio equipment (Regulation (EU) 2022/30, EN 18031 standards). The Cyber Resilience Act (CRA) will gradually apply to other products with digital elements. If this concerns you, address it at the design stage.

Wondering whether an assembly of parts that are already CE marked needs CE too? The answer is in The parts are CE marked. Does the assembly need CE too?

Free PDF download

The complete CE guide as a PDF

All 11 guides in one document: directives, EMC and safety testing, technical documentation, manual and rating label. For printing and for your team.

We use your data only to provide the document and as per the boxes you checked. You can withdraw your consent at any time at sales@compteq.io. Controller: Compteq.io s.r.o. Privacy policy

Start with the first step

Based on your product description, the calculator identifies the rules, standards and tests and shows an indicative price. Reply within 24 hours; we can usually offer testing within a week.