Testing · troubleshooting

Failed EMC. What now?

A peak above the limit or a reset during a discharge is not the end of the project. Most problems are solved by inexpensive changes if you know where to look. We go through the fixes from the simplest to a design change.

Reading time 7 minutes6 levels of fixes

Short answer

First find out what interferes and where from. Then try fixes starting with the quickest and cheapest: cabling, grounding, ferrites and filters, firmware. Only when that is not enough, change the enclosure or the board design. Retest after every change.

The earlier, the cheaperChanging a cable takes minutes. A new board revision takes weeks and costs money for manufacturing. That is why it pays to test the prototype, not only the finished product before certification.

Find the cause first

Randomly adding ferrites sometimes helps, but often just moves the problem elsewhere. The test report and a few simple experiments usually show where to look:

We then pinpoint the exact spot on the board with a near-field probe. It shows which component or trace radiates the most.

Fixes from the cheapest

The order is indicative. Only testing shows what helps your particular device.

1. Cabling

effort: low

Cables are the most common antenna. Current flowing along them in the same direction there and back (common-mode current) radiates even when the device itself is fine. A cable also brings interference inside, for example during the fast transient test.

  • Shorten cables and route them close to the chassis, not loosely in the air.
  • Use twisted pairs for signals and power.
  • Terminate the cable shield around the full circumference of the connector, not with a pigtail.
  • Separate power and signal wires; do not run them in one bundle.

2. Chassis bonding and grounding

effort: low

Shielding and filters only work if they have somewhere to divert the interference. A long, thin wire to the chassis has high impedance at high frequencies and hardly helps.

  • Bond to the chassis short and wide (strap, direct contact), not with a long wire.
  • Ensure conductive contact between the cover and the enclosure; remove paint at contact points.
  • Connect metal connectors and their shields directly to the chassis.
  • Check where the electronics ground connects to the chassis and whether unnecessary loops are formed.

3. Ferrites and filters

effort: low to medium

A ferrite ring on a cable suppresses common-mode current. It usually helps in the range of tens to hundreds of MHz. A filter on the power input reduces conducted emissions from switch-mode supplies and improves immunity.

  • Ferrite rings or clamp-on ferrites on the cables where peaks showed up.
  • An AC or DC filter on the power input.
  • Fill capacitors and chokes into unpopulated positions on the board.
  • For immunity, add surge and ESD protection (e.g. TVS diodes) on the interfaces.

4. Firmware tuning

effort: medium

A lot of interference comes from clocks and fast signal edges. Some of it can be reduced by configuration alone, without touching the hardware. Firmware also helps with immunity: the device recovers by itself after a disturbance.

  • Enable spread-spectrum clocking if the interfaces tolerate it.
  • Slow down output edges (GPIO and bus slew-rate settings).
  • Disable unused peripherals, clock outputs and buses.
  • Move switching and communication frequencies out of problematic bands.
  • For immunity: watchdog, communication checks and retries, safe return to operation.

5. Enclosure and shielding

effort: medium to higher

A metal enclosure shields only as well as its parts are bonded together. Long slots and seams radiate like antennas themselves. A plastic enclosure does not shield at all.

  • Conductive gaskets or spring contacts between the cover and the enclosure, more screws.
  • Several small openings instead of one long slot.
  • A shielding can over the problematic part of the board.
  • For plastic, a conductive coating inside the housing or internal shielding.

6. Electronics design

effort: high

When the board or the circuit is the cause, other measures only mitigate the consequences. A design change means a new board revision, but it solves the problem at the root.

  • A PCB stackup with a solid ground plane under fast signals.
  • Short current loops in switch-mode supplies and decoupling capacitors.
  • Placement: fast circuits away from connectors and board edges.
  • Filtering and protection right at the connectors.
  • Choosing components with slower edges or lower emissions.
Mind safetyFilters with capacitors to the chassis (Y capacitors) increase leakage current. For mains-powered equipment, it is limited by the electrical safety standards. A fix for EMC must not compromise safety.

How we handle it

  1. We measure the device in our EMC chamber and show you where and by how much it exceeds the limit.
  2. We look for the cause right at the chamber, together with you: rerouting cables, near-field probing, disconnecting parts.
  3. We try fixes on site (ferrites, bonding, temporary shielding, firmware settings) and retest immediately.
  4. You get the result with before-and-after charts and a recommendation on what to implement in production.

When the problem lies in the board or enclosure design, our engineering team proposes a fix and we retest the next revision right away. We can usually offer testing within a week.

How to prevent it next time

Free PDF download

The complete CE guide as a PDF

All 11 guides in one document: directives, EMC and safety testing, technical documentation, manual and rating label. For printing and for your team.

We use your data only to provide the document and as per the boxes you checked. You can withdraw your consent at any time at sales@compteq.io. Controller: Compteq.io s.r.o. Privacy policy

Did your device fail?

Get an indicative price for pre-compliance testing and root-cause analysis. We reply within 24 hours.