Short answer
Whoever sells the lamp under their own name is its manufacturer. They must assess conformity, compile technical documentation, draw up an EU declaration of conformity and affix the CE marking to the lamp. For luminaires, the manufacturer does this alone, without a notified body.
Which rules apply
- Electrical safety: Directive 2014/35/EU (LVD). It applies to every mains-powered lamp. The main standards are EN 60598-1 and, for table and floor lamps, EN 60598-2-4.
- Hazardous substances: Directive 2011/65/EU (RoHS). You demonstrate it with declarations from your parts suppliers.
- Electromagnetic compatibility: Directive 2014/30/EU (EMC). Whether it applies to you depends on the electronics. See the next section.
Is EMC needed?
It depends on whether the lamp has its own electronics.
- Without electronics (just a lampholder, a mechanical cord switch and a replaceable bulb with its own CE): EMC tests are usually not needed. Emissions and immunity are handled by the bulb, which has its own declaration. You briefly justify this in the technical documentation.
- With electronics (built-in LED module or strip with a driver, dimmer, touch switch, USB charging): EMC is tested. Emissions to EN IEC 55015, immunity to EN 61547 and, for mains power, also harmonics and flicker to EN IEC 61000-3-2 and EN 61000-3-3.
What is tested for safety
The EN 60598 standard covers the whole luminaire. For a simple lamp, these are the main points:
- Temperature rise: how hot the lamp gets with the highest permitted bulb wattage and whether the plastics and cord can withstand it.
- Plastics, heat and fire: parts that hold live parts must resist heat and must not ignite easily.
- Cord: anchorage against pulling and twisting, a cord entry without sharp edges.
- Insulation and electric strength: a lamp with a cord without a protective earth conductor must have double insulation (protection class II).
- Stability: a portable lamp must not tip over easily.
- Marking and manual: manufacturer, type, voltage, maximum bulb wattage and instructions in the language of the country of sale.
Watch out with 3D printing
Common 3D printing materials soften at low temperatures: PLA from about 60 °C, PETG from about 80 °C. For a lamp, therefore, watch:
- The distance between the shade and the bulb. The closer it is, the hotter the plastic gets.
- The maximum wattage on the label. A classic 60 W incandescent bulb, which gets much hotter than an LED, also fits an E27 lampholder. So state on the label and in the manual the type and maximum wattage with which you assessed the lamp.
- Keep live parts inside certified components. A printed part should only hold the lampholder, not replace its insulation.
Several variants, one assessment
Same electrical parts and different shade shapes? You do not have to test every variant. The worst case is tested: the shade closest to the bulb (highest temperature) and the least stable shape. You then describe all variants in one technical file and one declaration of conformity.
What you can do yourself and where we help
You can do it yourself
- Collect the EU declarations of conformity and RoHS declarations from the suppliers of the lampholder, cord, switch and bulb.
- A description of the lamp, photos, drawings and a parts list.
- The label, manual and EU declaration of conformity. Our declaration of conformity template helps.
Where we help
- Analysis of the EN 60598 requirements for your specific lamp and a review of your documentation.
- Electrical safety tests in our own lab. If you need a report from an accredited test lab, we arrange it with a partner.
- For lamps with electronics, EMC testing in our own chamber. We can usually offer testing within a week.
What manufacturers forget
- Take-back: luminaires are electrical equipment. Manufacturers must meet the national WEEE obligations (Directive 2012/19/EU) in each country where they sell, usually through a collective compliance scheme.
- Identification on the product: the manufacturer’s name or trademark, postal address and type or batch number.
- Instructions and safety information in the language of the country of sale, including the maximum bulb wattage.
The complete CE guide as a PDF
All 11 guides in one document: directives, EMC and safety testing, technical documentation, manual and rating label. For printing and for your team.
Find out what your lamp needs
Select the Luminaires category in the calculator. It shows the directives, standards and an indicative price, and clearly marks what is not included. We reply to inquiries within 24 hours.